Hot Shoe Adapter (UPT_HS1)

The hot shoe adapter allows you to connect a separate external flash to the timer using a 3.5mm plug. The timer supports both high voltage and low voltage electronic flashes.

The external flash needs to be setup for manual mode when operating with the timer. Flash units with positive center pin are supported.

Camera Shutter Release Interface Adapter (UPT_CAB_INT1)

If you can connect the Timer to your camera using a shutter release cable. The shutter release cable supports single exposure as well as bulb mode exposures. Interface adapter electrically isolates the timer from your camera.

The camera shutter release interface adapter connects to one of the external sensor inputs using a 2.5mm plug. The other end accepts camera motor drive cable with 3.5mm (1/8") mono/stereo connector.

Use your existing shutter cables or purchase them from us. Standard Pocket Wizard cables are supported including pre-trigger cables as well as ACC type. Alternatively, connect your camera through a Pocket Wizard device for wireless operation (requires separate 3.5mm to 3.5mm stereo or mono mini phone cable, not included).

The cable length is 6 ft.

Requires camera specific shutter cable (sold separately). Pocket Wizard devices are not included.

Not for use with hot shoe adapter or flash.

Full functionality with UPT_KIT1B and UPT_KIT1C.

Camera Specific Shutter Cable - Canon Cameras - N3 Connector ( UPT_CAB_CAN2)

For triggering the electronic shutter release of Canon cameras equipped with a N3 Remote Terminal. For use with Shutter Release Interface Adapter. Similar in function to Pocket Wizard Cable CM-N3-ACC

From 3.5 mm (1/8") Stereo Mini phone To Canon N3.

Canon Digital:

• 50D, 40D, 30D, 20D, 10D, D60, D30
• 7D, 5D, 5D Mark II,
• 1D, 1D Mark II, 1D Mark II N, 1D Mark III, ID Mark IV
• 1Ds, 1Ds Mark II, 1Ds Mark III

Canon Film:

• EOS 1, EOS 1V, EOS 1V-HS
• EOS 3

Requires Camera Shutter Release Interface Adapter UPT_CAB_INT1.

The cable length is 2 ft.

Other camera connector types are available upon request. Please contact us for availability and pricing.

Camera Specific Shutter Cable - Canon EOS Cameras - E3 Connector ( UPT_CAB_CAN3)

For triggering the electronic shutter release of Canon cameras equipped with a E3 Remote Terminal. For use with Shutter Release Interface Adapter.

From 3.5 mm (1/8") Stereo Mini phone To Canon E3.

Canon EOS Digital (E3 Connector):

• 300D, 350D, 400D, 450D, 500D, 550D, 1000D
• Rebel, XT, Xti, Xsi, T1i, T2i
• G10, G11

Canon EOS Film (E3 Connector):

• 30, 33, 50E, 300, 300V, 3000, 50, 500, 500N, 300X, KISS, NEW KISS, 7, 7, 7s, 7N, Rebel G, Rebel X, Rebel XS

Requires Camera Shutter Release Interface Adapter UPT_CAB_INT1.

The cable length is 2 ft.

Other camera connector types are available upon request. Please contact us for availability and pricing.

Camera Specific Shutter Cable - Nikon Cameras - 10Pin Connector ( UPT_CAB_NIK2)

For triggering the electronic shutter release of Nikon cameras equipped with a 10 pin Remote Terminal. For use with Shutter Release Interface Adapter. Similar in function to Pocket Wizard Cable N90M-ACC-ND.

From 3.5 mm (1/8") Stereo Mini phone To Nikon 10 pin connector.

Nikon Digital:

• D1, D1X, D1H
• D2X, D2Xs, D2H, D2Hs
• D3, D3s
• D300, D300s, D700
• Does NOT work with D100 or D200

Nikon Film:

• N90, N90s, F5, F6, F100

Fuji Digital:

• S3 Pro, S3 Pro UVIR, IS Pro, S5 Pro

Requires Camera Shutter Release Interface Adapter UPT_CAB_INT1.

The cable length is 2 ft.

Other camera connector types are available upon request. Please contact us for availability and pricing.

IR Extension Cable (UPT_IRX1)

The timer can activate your camera shutter using an infra-red signal. This is a similar type of transmission used by your TV remote. The timer comes with a built in infra-red transmitter.

In some cases you may need to extend the operating range of the timer or to use your camera behind a corner.  This is where IR extension cable comes-in, allowing you to reach further. The extension cable connects to one of the external sensor inputs using a 2.5mm plug.

The cable length is 18 ft.

Compatible with UPT_KIT1B and UPT_KIT1C.